upload
Sherline Products Inc.
産業: Industrial machinery
Number of terms: 990
Number of blossaries: 0
Company Profile:
デジタル読み出しの動きを決定する、ハンド ホイールの卒業式を見てのではなく番号を読み上げるスクリーンと電子の箱を組み込みます。場合は 2 つの利点: これらの視力は、ハンド ホイールに小さなマークと 2 より読みやすく) それの追跡累計走行距離長い動きを作るときにハンド ホイールの回転数をカウントする必要はありません。これは、エラーの一般的な原因を排除することができます。
Industry:Industrial machinery
基本モデルのマシンでは、プレーンなハンド ホイールが使用されます。彼らはレーザー彫刻 50 マーク (インチ) または 100 マーク (メトリック) と参照の番号です。調節可能なゼロ場合任意の時点で停止、ローレット ハンド ホイールの中心を緩め、ハンド ホイールの位置を移動することがなく、次のカットを開始する前にゼロのマークに戻るレーザー刻まれた襟を回転することができます。あなたの深さを作り、ランダムな番号ではなくゼロから始めているし、の計算を簡単にカットするたびを意味します。これは最終的に小さいミスを意味します。4400、4500 シリーズ旋盤、5400、2000年シリーズ ミルズ標準的な装置としてこれらのアップグレードの場合が含まれます。
Industry:Industrial machinery
この関数は縦か斜め切削または掘削する側に側から回転することができます。それまたは 2000年シリーズ ミルズのデザインに含まれる 5000/5400 シリーズ ミルズに (P/N 3700) オプションとして追加できます。
Industry:Industrial machinery
On the 2000-series mills, a "ram" is added that allows the entire column to be moved in and out and swung from side to side. It is designed based around the movements of the machine shop workhorse - the Bridgeport® mill.
Industry:Industrial machinery
The normal (rear) position gears the motor down about 2:1 for a maximum speed of about 2800 RPM. The "High Torque" position (closest to the headstock) gears it about 4:1 for lower speed but more torque when needed for heavy cuts.
Industry:Industrial machinery
ドライブのスピンドル、滑車を通してケブラー補強ウレタン ベルト。
Industry:Industrial machinery
Moves the headstock 1. 25" further out from the saddle to increase the "throat" distance (distance between cutter and column). It is optional on 5000-series mills, standard on 5400-series mills and not needed on 2000-series mills because the ram can be used to adjust this distance.
Industry:Industrial machinery
まっすぐ上下に整列ヘッドを維持する列サドルにスロットに収まるように精密地面のキー。2 番目のスロットは、90 ° 水平フライス盤のヘッド ストックを検索するも提供しています。このキーを削除して、主軸の回転ベベル任意の角度でカットすることができます。おおよその角度スケールは参照のためにサドルに刻まれたレーザーです。
Industry:Industrial machinery
The lock works like tightening two nuts against each other on a threaded shaft to reduce play in the threads. Backlash is the pause in travel when changing direction of rotation of any threaded crew. Because both sides of the thread don't rub on the nut at the same time (they would quickly wear out), one surface is pulling or pushing the nut when the screw is turned. When you stop and change directions, the screw turns a slight amount while the thread picks up the other side and begins to move the nut in the other direction. The looser the fit of the threads, the more "backlash" occurs. In essence, it is the amount you can turn the handwheel in the reverse direction before movement occurs on an axis. . An adjustment is provided on the X- and Y-axes to reduce the leadscrew backlash. Backlash is not a "fault" of a machine, it is simply a physical reality that must be taken into account when machining. You adjust to a known or acceptable amount using the locks and then remove it from the machining operation by always approaching your cut from the same direction with the backlash already eliminated before the cut begins.
Industry:Industrial machinery
ねじ加工動きはない必要または望ましい操作中の場所でテーブルをロックするサドルの前面に 1 バレル = ロックを通過します。
Industry:Industrial machinery